Retaining Walls in Phoenix, AZ
Last updated: November 2026
Estimate your wall costA retaining wall holds soil so a patio, pool deck, or driveway can sit flat where the lot slopes. In the Phoenix Valley that shows up on hillside lots, around pools, along washes, and anywhere a builder graded the yard into levels. This guide covers typical 2026 price ranges per foot and per project, when engineering starts, how monsoon drainage is supposed to work, and what Phoenix, Mesa, Gilbert, Chandler, Queen Creek, Surprise, Buckeye, Scottsdale, Peoria, and Glendale each require. Dollar figures are typical ranges from named sources, or multiplication of those ranges. They are not a quote.
Retaining wall or block fence?
A block fence has the same soil level on both sides. A retaining wall has more soil on one side. A few feet of difference changes the footing, the steel, the drainage, and the permit. Tell contractors about any grade change when you ask for a bid. Freestanding wall pricing is in the block wall cost guide. A wall that is already leaning or cracking is in the repair guide.
You are usually looking at a retaining wall when:
- One yard, patio, or side slope sits higher than the other.
- The lot is in the foothills: north Scottsdale, north Phoenix, Cave Creek, the edges of Peoria, or South Mountain slopes.
- A pool or raised deck is cut into a grade. A pool next to a wall is a surcharge, and the permit rules change.
- Monsoon runoff is cutting a slope or a wash bank.
- A low planter still holds soil. Short planters often stay under the permit line. Tall ones do not.
Materials and typical installed ranges
| Material | Typical installed cost | Notes |
|---|---|---|
| CMU (cinder) block | $20–$35 per sq ft, or about $60–$210 per linear foot for 3–6 ft walls | Common Valley choice. Can be stuccoed to match the house (HomeGuide) |
| Engineered block retaining wall, local | $120–$250 per linear foot for 3–6 ft | Phoenix contractor range for 2026, including the engineered condition (New Era Masonry) |
| Segmental (interlocking) block | $15–$35 per sq ft, or $45–$210 per linear foot for 3–6 ft walls | Dry-stacked, often with geogrid behind it (HomeGuide) |
| Poured concrete | $25–$100 per sq ft in Phoenix | Strong, needs forms (Angi Phoenix) |
| Natural stone | $35–$75 per sq ft in Phoenix | Fits desert lots. Labor is heavy (Angi Phoenix) |
| Gabion | $10–$40 per sq ft in Phoenix | Drains freely (Angi Phoenix) |
| Timber | $15–$30 per sq ft in Phoenix | Lower up front, and Valley sun wears it out faster (Angi Phoenix) |
HomeGuide's block retaining range and Angi's poured-concrete range are different products. A bid should name the material, the height from the footing, and what is behind the wall.
Price per project
Angi says Phoenix homeowners spend about $2,381 to $7,333 on a retaining wall, with an average around $4,692 (Angi, updated 2026). By the foot, Angi lists about $90 to $150 per linear foot for a 3-foot wall and $180 to $300 per linear foot for walls up to 6 feet. Those per-foot bands are not CMU-specific.
For an engineered block wall, use the local contractor band and multiply. These totals are arithmetic from $120 to $250 per linear foot. They do not add a separate engineer, a permit, or a hillside access problem.
| Engineered block wall | How the range is built | Typical range |
|---|---|---|
| 20 linear feet, 3–6 ft | 20 × $120–$250 | about $2,400–$5,000 |
| 40 linear feet, 3–6 ft | 40 × $120–$250 | about $4,800–$10,000 |
| 60 linear feet, 3–6 ft | 60 × $120–$250 | about $7,200–$15,000 |
Angi also publishes a Phoenix length table for a poured-concrete wall 3 to 6 feet tall. Use it only for that material (Angi Phoenix):
| Length | Angi published range |
|---|---|
| 10 ft | $900–$3,000 |
| 20 ft | $1,800–$6,000 |
| 50 ft | $4,500–$15,000 |
| 100 ft | $9,000–$30,000 |
Face area. One Arizona hardscape company quotes about $25 to $60 per square foot of face for standard concrete block and $45 to $90 for decorative or stone-veneer walls (Solterra Hardscape). Multiply height by length. A 4-foot by 20-foot wall is 80 square feet of face.
Lines that sit outside the per-foot price
Angi publishes these Phoenix-area add-ons (Angi Phoenix):
- Structural engineering: about $800 to $2,000, or about 5% to 15% of the project. Angi says you need an engineer if the wall is more than 4 feet tall.
- Building permit: about $100 to $600, more on a larger valuation.
- Land grading: about $900 to $3,300.
- Excavation to fix drainage on an existing wall: about $60 to $70 per linear foot.
- Slope: labor can run 50% or more higher, because the crew steps the dig or terraces the hill.
- Caliche and expansive clay: more excavation time and more reinforcement. Angi flags both for Phoenix. There is no single published caliche surcharge.
HomeGuide lists a French drain at about $10 to $35 per linear foot as a drainage add-on on block wall work (HomeGuide). That is a national figure for the drain, not a full retaining wall.
Demolition of a concrete wall, when an old wall has to come out first, is about $5 to $16 per linear foot (HomeGuide, concrete removal). Retaining-wall removal is at the high end of that kind of work because the dirt behind the wall has to move too.
Engineering above about 4 feet
A practical Valley rule: once a retaining wall is around 4 feet, or it holds a pool, driveway, slope, or structure, budget a permit and stamped engineering. Angi uses that 4-foot line for bringing in a structural engineer (Angi Phoenix). Several Valley cities write a version of it into the code. The City of Phoenix is stricter than 4 feet.
Cities do not measure height the same way. Phoenix often measures a retaining wall from the top of the footing. Chandler and Surprise measure from the bottom of the footing. The same wall can fall on different sides of the line.
| City | When retaining work needs a permit or engineering | Source |
|---|---|---|
| Phoenix | Over 3 ft from the top of the footing to the top of the wall, or any height with a surcharge (house, driveway, pool, or a fence on the wall or within 3 ft uphill). Structural calculations required over 3 ft. Any fence on a retaining wall needs calculations. Combined height over 9 ft needs zoning approval first | City of Phoenix |
| Scottsdale | Engineered plans for every retaining wall | City of Scottsdale |
| Chandler | Over 4 ft from the bottom of the footing, or any surcharge. Any fence on a retaining wall needs a permit. 4-inch walls are not approved for retaining | City of Chandler |
| Surprise | Over 4 ft from the bottom of the footing, or any surcharge | City of Surprise code amendments |
| Gilbert | Reportedly over 4 ft, or any height with a surcharge. Confirm with the Town at 480-503-6700 | Town of Gilbert |
Other Phoenix rules worth pricing in (City of Phoenix):
- A single retaining wall is limited to 40 inches in front or street-side yards and 6 feet in interior side and rear yards.
- Terraced walls need horizontal space between them equal to the lower wall's height, and at least 3 feet.
- Hillside lots are reviewed case by case.
Arizona requires a licensed contractor for a job that needs a permit or costs more than $1,000. Check the license with the Arizona Registrar of Contractors. Call Arizona 811 at least two working days before anyone digs. The full fence-and-wall table is in the permit guide.
Drainage
Most retaining-wall failures in the Valley start with water. A monsoon storm can soak the soil behind a wall quickly, and wet soil pushes harder than dry soil. Clay that swells when wet adds another push. Angi calls out monsoon drainage and expansive clay as Phoenix-specific reasons walls need more than a stack of block (Angi Phoenix).
A properly built wall usually includes:
- Gravel backfill immediately behind the wall, so water drops instead of standing against the block.
- A perforated drain pipe at the base, daylighted or tied to a drain.
- Weep holes through the wall.
- Filter fabric so soil does not fill the gravel.
- Grade at the top that sends runoff away from the wall.
Phoenix requires retaining walls to be shown on grading and drainage plans (City of Phoenix). If a bid never mentions drainage, ask where the water goes. Fixing a wall that was built without it is its own project: Angi lists about $60 to $70 per linear foot to excavate and correct drainage.
The National Weather Service treats the Arizona monsoon as June 15 through September 30 (NWS Phoenix). That is the season when a missing drain shows up as a bow, a stair-step crack, or a lean. Those symptoms are covered in the repair guide.
City notes
The per-foot ranges do not change because you cross a city line. Engineering, drainage review, slope, and HOA finishes do.
Phoenix
Over 3 feet from the top of the footing, budget a permit and structural calculations. A fence on top always needs calculations. Hillside and preservation areas, including many South Mountain and north Phoenix slopes, are reviewed site by site, so a short wall on a steep lot can still need a custom design. Flat lots in the central city still need drainage if any soil is retained. Browse Phoenix contractors.
Mesa
Mesa's published residential FAQ is aimed at fences more than retaining walls, so call Development Services before you assume a short retaining wall is exempt. Shared property-line walls that also hold a grade need the neighbor's agreement plus whatever the city requires. Browse Mesa contractors.
Gilbert
Gilbert is reported to require a permit and engineering once a retaining wall is over about 4 feet, or at any height with a surcharge. Confirm at 480-503-6700. HOA architectural rules in master-planned neighborhoods often dictate the finish on the face everyone sees, which is a stucco or decorative-block line on top of the structural price. Browse Gilbert contractors.
Chandler
The 4-foot line is measured from the bottom of the footing, so a wall that looks like 3 feet above grade can still need a permit once the footing thickness is counted. A fence on top needs a permit at any height. Four-inch block is not an approved retaining system. Zoning clearance still applies to the fence portion. Browse Chandler contractors.
Queen Creek
New lots and wash edges are where short "yard leveling" walls turn into real retaining walls. Masonry in town has to follow a standard detail or engineered drawings (Town of Queen Creek). A standard fence detail is not a retaining design. If the wall holds soil, ask the town whether your height needs a registered engineer. Browse Queen Creek contractors.
Surprise
Retaining walls over 4 feet from the bottom of the footing, or any wall with a surcharge, need a permit under the city's code amendments. Pool barriers are a separate permit even when the fence itself would have been exempt. Master-planned yards add HOA review. Browse Surprise contractors.
Buckeye
The city publishes a retaining-wall checklist. Use that packet instead of borrowing Phoenix's 3-foot number (City of Buckeye). Larger lots mean longer walls, more grading, and a better chance of caliche in the footing trench. Browse Buckeye contractors.
Scottsdale
Every retaining wall needs engineered plans approved by the city, including short ones. That engineering line (Angi's published range is about $800 to $2,000, and it can sit outside a per-foot bid) belongs in a Scottsdale budget from the first conversation. North Scottsdale slopes and boulder outcrops are where terracing, drainage, and access dominate the price. Architectural committees often specify the visible finish. Browse Scottsdale contractors.
Peoria
Confirm retaining-wall height and submittals against the city's fence and block wall checklist rather than a neighboring city's rule (City of Peoria). North Peoria slopes behave more like north Scottsdale. Flat west Peoria walls are more often a simple grade change between lots, and they still need a drain if they hold soil. Browse Peoria contractors.
Glendale
Glendale's published amendments are clearer about tall fences and pool barriers than about a universal retaining-wall height. Call the building department before you treat a short Glendale retaining wall as exempt, and use the permit guide as the checklist of what to ask. Older lots with shared walls need neighbor sign-off when the wall on the line is also holding soil. Browse Glendale contractors.
Questions to ask a retaining wall contractor
- Does this wall need a permit and an engineer in my city, and who hires the engineer?
- How tall is it from the bottom of the footing, not only above the dirt you can see?
- What is behind the wall: gravel, drain pipe, fabric, geogrid?
- Where does the water come out?
- Is there a pool, driveway, fence, or slope above the wall, and is that load in the design?
- How will you handle caliche if you hit it?
- What is your Arizona ROC license number, and what does the warranty cover?
Frequently asked questions
How much does a retaining wall cost in Phoenix?
Angi reports Phoenix homeowners spend about $2,381 to $7,333 on a retaining wall, with an average around $4,692. By the foot, Angi lists about $90 to $150 per linear foot for a 3-foot wall and $180 to $300 for walls up to 6 feet. A Phoenix contractor lists 2026 engineered block retaining walls at $120 to $250 per linear foot for walls 3 to 6 feet tall. Those are typical ranges from published sources, not a quote.
How much is a whole retaining wall project, not just per foot?
Angi's Phoenix project range is about $2,381 to $7,333. Using a local contractor's $120 to $250 per linear foot for an engineered block wall, 20 feet is about $2,400 to $5,000 and 40 feet is about $4,800 to $10,000 before a separate engineering invoice, permit, or a steep slope. Angi also publishes poured-concrete length ranges, such as about $1,800 to $6,000 for 20 feet. Confirm which material the bid is actually using.
When does a Phoenix retaining wall need an engineer?
Plan on engineering once the wall is around 4 feet, and sooner in some cities. The City of Phoenix requires structural calculations for retaining walls over 3 feet measured from the top of the footing, and for any fence on a retaining wall. Chandler and Surprise use about 4 feet measured from the bottom of the footing. Scottsdale requires engineered plans for every retaining wall. Angi also says a structural engineer is needed when the wall is taller than 4 feet. Any wall holding a pool, driveway, or building usually needs engineering at any height.
How tall can a retaining wall be without a permit in Phoenix?
In the City of Phoenix, a retaining wall 3 feet or less, measured from the top of the footing to the top of the wall, does not need a permit unless it supports a surcharge such as a house, driveway, pool, or a fence on top or within 3 feet of the uphill side. Over 3 feet needs a permit and structural design calculations. Neighboring cities measure height differently, so check the city you are actually in.
Why do retaining walls fail in Phoenix?
Water is the usual cause. Monsoon rain soaks the soil behind the wall and pushes on it. A wall without gravel backfill, a drain pipe, and weep holes can bow, crack, or tip. Caliche makes the excavation harder, and clay soils that swell when wet add pressure. Angi notes that Phoenix walls need drainage built for monsoon rain and reinforcement where clay shifts.
Can I put a block fence on top of a retaining wall?
Usually yes, and it changes the engineering. Phoenix requires structural calculations for any combination of retaining wall and fence, and zoning approval when the combined height exceeds 9 feet. Chandler requires a permit any time a fence sits on a retaining wall. Tell every bidder if a fence is going on top.
What is the cheapest retaining wall material in the Phoenix area?
For most yards, dry-stack segmental concrete block is among the more budget-friendly options that still holds up, and it does not need stucco. Standard CMU is the common choice when the wall should match a block fence or a stucco house. Wood timbers can cost less up front and weather faster in Valley sun. Poured concrete and natural stone cost more.
Find a retaining wall contractor
Many block wall contractors in the directory also build retaining walls. Start with the Valley list or your city: Phoenix, Mesa, Chandler, Gilbert, Scottsdale, Peoria, Glendale, Surprise, Queen Creek, Buckeye, Tempe, Goodyear, Avondale, or Cave Creek.
Related guides: block wall cost, block wall repair, and permits by city. Get at least three written bids, and make sure each one spells out drainage and engineering.
Prices are typical ranges from the sources linked above, not quotes. Permit rules change. Confirm them with your city before you build.